Prepare 200-601 exam with the help of dumps. You can Pass your Cisco 200-601 exam with real exam question answers. Authentic 200-601 study material available for your IT exam preparation. Your can easily prepare and pass your Certification exam on first attempt. You can get all Cisco exam study material and 200-601 exam related information here on dumps4download website.
Our all 200-601 preparation material fully verified by IT professionals. we are fully sure that you will love to prepare your exam with us. These are the exam question answers that you can get free of cost here on dumps4download. If you want to get complete 200-601 PDF and VCE you can choose our Premium files. 100% guaranteed that you will pass your Managing Industrial Networks for Manufacturing with Cisco Technologies exam Dumps4download exam preparation material.
Get Latest Dumps Question Answers For Cisco 200-601 Exam - Dumps4download
The exam Managing Industrial Networks for Manufacturing with Cisco Technologies (CCNA IMINS2) certification exam (200-601) is a 90 minute, 65 – 75 question assessment. This exam tests concepts and technology commonly found in the automated manufacturing environment. This exam tests candidates on the Common Industrial Protocol (CIP) and ProfiNET industrial protocols and the underlying support network infrastructure design to maximize efficiency within Industrial Ethernet.
The following topics are general guidelines for the content likely to be included on the exam. However, other related topics may also appear on any specific delivery of the exam. In order to better reflect the contents of the exam and for clarity purposes, the guidelines below may change at any time without notice.
The following course is the recommended training for this exam.
- Managing Industrial Networking for Manufacturing with Cisco Technologies (IMINS2) E-Learning
Courses listed are offered by Cisco Learning Partners-the only authorized source for Cisco IT training delivered exclusively by Certified Cisco Instructors. Check the List of Learning Partners for a Cisco Learning Partner nearest you.Exam Number : 200-601 IMINS2Associated Certifications : CCNA IndustrialDuration : 90 Minutes (65 - 75 questions)Available Languages : EnglishRegister : Pearson VUE
Refer to the exhibit.
You are required to implement traffic segmentation in the network. See the table for
relevant device details:
L2SW4, L2SW5, and L2SW6 are connected to L3SW1 with 802.1Q trunks with VLAN 191
and VLAN 398 allowed on the trunk.
You have the following information from L3SW1:
L3SW1# show run interfaces
no ip address
ip address 10.2.2.2 255.255.255.248
ip address 10.10.27.126 255.255.255.192
ip address 10.20.20.1 255.255.255.248
ip address 10.15.153.1 255.255.255.0
L3SW1# show ip route
*** Output Omitted ***
10.0.0.0/8 is variably subnetted, 5 subnets, 3 masks
C 10.2.2.1/29 is directly connected, Vlan2
C 10.10.27.64/26 is directly connected, Vlan191
C 10.15.153.0/24 is directly connected, Vlan398
C 10.20.20.0/29 is directly connected, Vlan200
S 10.200.200.0/24 [1/0] via 10.20.20.2
S* 0.0.0.0/0 [1/0] via 10.2.2.1
You are required to implement a configuration that will meet the following connectivity
• The Administrator's Station must have full access to PanelView
• PanelView should have limited access, based on specific TCP ports, to PLC#1 and
• The Administrator's Station should have no access to PLC#1 and I/O#1
• PLC#1 and I/O#1 should be able to communicate with each other on any port
Which action will allow you to meet the connectivity requirements?
A.Put interface VLAN 191 and interface VLAN 398 into different Virtual Routing and
Forwarding (VRF) instances on L3SW1
B.Deploy an inbound ACL on interface VLAN 191 to control the traffic from the
Administrator's Station and PanelView to PLC#1 and I/O#1
C.No change is required, the traffic is already limited appropriately by the VLAN
D.Implement an ACL on Firewall1 to control the traffic flow between VLAN 191 and VLAN
Your supervisor calls you and tells you that one of the Stratix 5700 switches is not assigning all CIP explicit messages to the proper QoS queue. The switch was deployed with the ab-global macro and CIP explicit messages were previously being assigned to the proper QoS queue. You suspect the access-lists associated with the ab-global macro have been changed. Look at the following access list from the switch configuration: access-list 101 permit udp any eq 2222 any dscp 55 access-list 102 permit udp any eq 2222 any dscp 47 access-list 103 permit udp any eq 2222 any dscp 43 access-list 104 permit udp any eq 2222 any access-list 105 permit udp any eq 44818 any access-list 105 permit tcp any eq 44816 any What needs to be done to fix the above access list?
A.Access list 105 should reference udp port 44816
B.Access lists 101-104 should reference udp port 2212
C.Access list 105 should reference tcp port 44818
D.Access list 104 should be a deny access list rather than a permit access list
Refer to the exhibit. Which lines represent a CIP connection being established between two devices?
A.2914 and 2915
B.2918 and 2921
C.2920 and 2924
D.2937 and 2940
Refer to the exhibit.
Which three options are needed to configure NAT on router GW so PC1 and PC2 will be
able to ping 203.0.113.1? (Choose three)
ip nat inside
ip nat outside
B.ip access-list standard ACL_NAT
permit 10.1.1.0 0.0.0.255
C.ip nat inside source static tcp 10.1.1.0 80 interface Ethernet1 80
ip nat outside
ip nat inside
E.ip nat inside source list ACL_NAT interface Ethernet1 overload
F.ip access-list extended ACL_NAT
permit tcp 10.1.1.0 0.0.0.255 any eq 80
Which statement is true regarding ProfiSAFE?
A. ProfiSAFE traffic must be carried on a network that is physically separated from
B. ProfiSAFE relies on the error detection mechanisms of Ethernet and TCP/IP to
determine if there are network errors
C. ProfiSAFE can be used in safety applications up to Safety Integrity Level 3 (SIL3)
D. ProfiSAFE is only used by ProfiBUS PA and ProfiBUS DA devices
Which CLI command will display IGMP snooping information in a Cisco IE2000 or Stratix 5700 switch?
A. switch#show snooping ip igmp
B. switch#show igmp snooping
C. switch#show ip igmp snooping
D. switch#show ip snooping
Which describes a best practice rule for controlling traffic between the corporate network
and the controls network?
A. Outbound traffic from the control network to the corporate network and outbound traffic
from the corporate network to the control network can be restricted based on source and
destination address only.
B. Outbound traffic from the corporate network to the control network should be restricted
but outbound traffic from the control network to the corporate network should not be
C. Outbound traffic from the control network to the corporate network should be restricted
based on source and destination address and service only.
D. Outbound traffic from the control network to the corporate network should be
restricted based on source and destination address, service, and port.
Given the CIA triad elements, which ensures first that the data is encrypted and secure,
second that the data is trustworthy, and third that the data is accessible by those who need
Which two actions are examples of network device hardening for Cisco Industrial Ethernet
Switches? (Choose two)
A. Disable unused services
B. Shutdown network ports which are not in use
C. Only allow administrative access using Telnet
D. Deploy IP67 versions of Cisco Industrial Ethernet Switches
E. Set the native VLAN on all trunk ports to VLAN 1
What are three Cisco best practices for running I/O control traffic in a wireless environment? (Choose three)
A. 3200 packets per second and 20% bandwidth for HMI and maintenance traffic.
B. 2200 packets per second and 20% bandwidth for HMI and maintenance traffic
C. I/O control traffic can be run on 2.4 or 5 GHZ channels
D. I/O control traffic should be run on 5GHZ channels only
E. Standard I/O RPIs less than 20ms are not practical for wireless media because the maximum latency and jitter become comparable or greater than the RPI
F. Standard I/O RPIs less than 10ms are not practical for wireless media because the maximum latency and jitter become comparable or greater than the RPI