Prepare 600-601 exam with the help of dumps. You can Pass your Cisco 600-601 exam with real exam question answers. Authentic 600-601 study material available for your IT exam preparation. You can easily prepare and pass your Certification exam on first attempt. You can get all Cisco exam study material and 600-601 exam related information here on dumps4download website.
Our all 600-601 preparation material fully verified by IT professionals. We are fully sure that you will love to prepare your exam with us. These are the exam question answers that you can get free of cost here on dumps4download. If you want to get complete 600-601 PDF and VCE you can choose our Premium files. 100% guaranteed that you will pass your Implementing Cisco Threat Control Solutions (SITCS) exam Dumps4download exam preparation material.
Get Latest Dumps Question Answers For Cisco 600-601 Exam - Dumps4download
What is the purpose of Spanning Tree Protocol?
A. to prevent routing loops
B. to create a default route
C. to provide multiple gateways for hosts
D. to maintain a loop-free Layer 2 network topology
E. to enhance the functions of SNMP
Which three of the following components must be elected before the Spanning Tree Protocol can converge in a switched LAN? (Choose three.)
A. designated ports
B. duplex operating mode
C. fast mode ports
D. root bridge
E. root ports
F. BDPU priority
What are two benefits of a star network topology? (Choose two.)
A. Disruption of the entire network is not required when adding new machines.
B. Any problem which leaves the network inoperable can be traced to the central hub.
C. This network type requires less cable as compared to linear bus topology.
D. The performance of one of the numerous nodes cannot reflect on the performance of other nodes.
E. The performance of the entire network is directly dependent on the performance of the hub.
Which two statements are correct for a safe wiring installation to the terminal block of the switch or endpoint? (Choose two.)
A. Insert a green ground wire into the terminal block that is marked RT for return.
B. Verify that DC power is live and within 24 VDC voltage range before starting wiring.
C. Verify that the DC power circuit includes an overcurrent protective device that limits the DC current to 5A.
D. Because this is a low-voltage DC circuit, anyone can install this wiring without electrical training or qualifications.
E. Connect the positive 24 VDC conductor to the V terminal and connect the negative 24 VDC return wire to the RT terminal.
F. A ground wire can optionally be connected to the screw terminal on the front of the switch.
Which two ports does EtherNet/IP use to communicate? (Choose two.)
A. TCP 44818
B. UDP 44818
C. TCP 502
D. UDP 502
E. TCP 2222
F. UDP 2222
Which option allows an EtherNet/IP I/O device to be safely installed where it is subject to water immersion?
A. The device is rated IP20 and the power wiring is installed securely to the terminal block.
B. The device is rated IP67 and a power cordset is used.
C. The device is rated IP67 and immersed to 10 m.
D. The device is rated IP20 and immersed to 10 m.
Refer to the exhibit. Which port should a PLC with IP address 192.168.3.65 be plugged into in order to communicate to the rest of the network?
Which of the following correctly pairs the dotted decimal subnet mask with the correct number of binary bits that represent the subnet mask?
A. 255.255.255.192 and /25
B. 255.255.255.248 and /28
C. 255.255.255.224 and /26
D. 255.255.255.248 and /27
E. 255.255.255.240 and /28
F. 255.255.255.240 and /16
Refer to the exhibit. Host 3 on Network A is sending data to Host 8 on Network B. Which address is the
default gateway of Host 3?
A. the address of the switch interface that is connected to router interface Fa0/0
B. the address of the switch interface that is connected to router interface Fa0/1
C. the address of the host that is connected to Network A
D. the address of the host that is connected to Network B
E. the address of the router interface Fa0/0
F. the address of the router interface Fa0/1
A small manufacturing company has a Class C network address on the plant floor and needs to create five subnets, each accommodating 25 endpoints. Which subnet mask needs to be configured?